If you’ve ever stood next to a drilling machine—whether in a shop making metal parts, a woodworking studio, or even a place building heavy construction equipment—you’ve probably heard someone talk about “feed rate” and not really gotten what they meant. I’ve been selling drilling machines for over a decade, and I can’t tell you how many times I’ve had new operators, small workshop owners, or even folks just starting out ask, “Wait, what actually is feed rate, and why does it matter so much?” Today, I’m breaking it down straight, no textbook jargon, just what I’ve learned from working with drilling machines every single day. Drilling Machine

First off, let’s keep it simple: feed rate is basically how fast your drill bit moves into the material you’re cutting. If you’ve ever cranked the handle on a manual drill press to push the bit through a piece of aluminum, or set the speed on a CNC drilling machine to feed the bit at a certain pace, that number you dial in or adjust is feed rate. It’s not the same as spindle speed—spindle speed is how fast the drill bit spins, right? Feed rate is movement forward, into the work. That’s a mix-up I see all the time, especially with new people.
Let me give an example. Say you’re drilling a hole in a ½-inch thick steel plate. If your feed rate is too slow, the drill bit will rub against the metal instead of cutting through it. That rubbing generates way more heat than it should. Heat kills drill bits fast—if you’re pushing too slow, your bit will dull in minutes, maybe even snap before you finish the hole. On the flip side, if feed rate is too fast, the bit is pushing so hard into the material that it can’t evacuate the chips (those little metal or wood shavings) fast enough. Those chips get stuck between the bit and the hole wall, which makes the bit bind, again leading to breaks, uneven holes, or even ruining the workpiece. I’ve had customers bring back drill bits that looked like they’d been chewed up by a machine, just because someone set the feed rate wrong.
Now, let’s talk about how feed rate is measured, because that’s another part that trips people up. For manual drill presses— the ones with the hand crank—feed rate is usually in inches per revolution (IPR) or millimeters per revolution (mm/rev). That means, for every full spin of the drill bit, how far it moves forward. For example, a common feed rate for drilling steel with a ½-inch bit might be 0.005 IPR—so each time the bit spins once, it moves 0.005 inches into the metal. For CNC drilling machines, which are super common in production shops these days, feed rate is often in inches per minute (IPM) or millimeters per minute (mm/min). That makes sense because CNC machines don’t have a manual hand crank, so they move the entire tool (or the worktable) at a set speed. To convert IPR to IPM, you just multiply IPR by the spindle speed in RPM (revolutions per minute). So if your spindle is spinning at 1000 RPM and your feed rate is 0.005 IPR, your IPM is 5 inches per minute. Got that? No fancy math, just basic multiplication.
Here’s where I’ve seen even experienced folks mess up: they don’t adjust feed rate based on the material. A feed rate that works for soft wood will be totally wrong for hardened steel, and vice versa. Let’s break down common materials:
-
Wood: Super forgiving, right? For drilling wood, you can run a pretty high feed rate—usually around 0.01 to 0.02 IPR. Wood doesn’t generate as much heat, and the chips (wood shavings) are big and easy to clear. I see people use the same feed rate for wood every time, and that works because it’s a soft, non-metallic material. But if you’re drilling plywood, which has layers of glue, you might want to slow down a tiny bit to keep the bit from tearing the veneer.
-
Aluminum: Aluminum is softer than steel, but it’s also “gummy”—the chips stick together more. So you can’t go too fast or too slow. For aluminum, I recommend a feed rate of 0.003 to 0.008 IPR, depending on the bit size. If you go too slow, the aluminum will build up on the bit (that’s called built-up edge, or BUE) which ruins the hole finish. If you go too fast, the chips get stuck and cause binding. A lot of small machining shops I work with have a standard feed rate for aluminum that they just stick to, and it works perfectly for most jobs.
-
Steel: This is the tricky one, especially alloy steel or hardened steel. For mild steel, a good starting point is 0.002 to 0.005 IPR. But if you’re drilling hardened steel, you need to slow way down—like 0.001 to 0.002 IPR. Hard steel doesn’t give easily, so pushing too fast will snap your bit instantly. I’ve had a customer come in last year with a stack of $50 drill bits, all broken, because he tried to drill hardened steel at the same feed rate he used for mild steel. Oops. We adjusted his feed rate, and now those same bits last him 10x longer.
-
Plastics: Plastics vary a lot—some are soft (like acrylic) and some are hard (like PVC). For acrylic, you want a higher feed rate (around 0.01 IPR) to prevent melting around the hole. For PVC, you have to be careful not to go too fast, because it can cause the plastic to crack. I tell folks to test a scrap piece first—always test a scrap! That’s a rule I live by, because every machine, every bit, even every batch of material can be a little different.
Now, let’s talk about how your drilling machine type affects feed rate. Not all drilling machines are the same, right? There’s manual drill presses, CNC drilling machines, radial drills, gang drills—each has its own way to set feed rate, and its own limits. For example, manual drill presses don’t have a built-in feed rate control, so you’re relying on the operator’s hand strength and judgment. That’s why I always tell small workshop owners with manual presses to get a feed rod or a digital feed rate gauge—those cheap add-ons take the guesswork out of cranking the handle. You can set how much you want the bit to move per revolution, so even a new operator can get consistent holes.
CNC drilling machines, on the other hand, have full control over feed rate, spindle speed, and every other setting. That’s why they’re so popular for production work—you can program a specific feed rate for each material, switch it in seconds, and every hole is identical. But I still see people new to CNC programming mess up the feed rate. They’ll set a super high feed rate to get the job done faster, but it ruins the tooling or the part. It’s not just about speed—it’s about balance. Too fast = broken tools, scrap parts. Too slow = wasted time, higher cost per part.
Another thing: drill bit size. The bigger the bit, the more feed rate you can usually use. A ¼-inch drill bit doesn’t need the same feed rate as a 2-inch drill bit. For a 2-inch bit drilling mild steel, you might run 0.005 IPR, but a ¼-inch bit would be 0.002 IPR. Small bits can’t handle as much force—they bend or break easily if you push too hard. I always advise customers to check their drill bit’s manufacturer guidelines, too—most bit brands have a recommended feed rate chart right on the box. It’s not a suggestion, it’s a starting point.
Wait, let’s address a common myth I hear all the time: “Faster feed rate means faster drilling time.” Yeah, but only up to a point. If you set a feed rate that’s within the bit and material limits, you do drill faster. But if you push past that limit, you’ll spend way more time replacing broken bits and fixing messed up parts than you would have if you’d taken the time to set the right feed rate. I had a customer a few months back who was running a small production line, and he was churning out 10 parts an hour—until his drill bits were breaking every 20 parts, and he had to spend 30 minutes every hour replacing them. Once he adjusted his feed rate to the recommended level, he was only doing 8 parts an hour, but he didn’t have any downtime for bit changes. He told me his overall production went up because he wasn’t wasting time on broken tools. That’s a real example, not some textbook story.
Now, why does this matter for you, especially if you’re looking for a drilling machine? If you’re buying a machine for your shop, make sure it has the feed rate control you need. If you’re a small workshop with only a few jobs, a manual drill press with a basic feed adjustment might work. But if you’re doing production work, you need a CNC drilling machine with variable feed rate control, maybe even a touchscreen that lets you save feed rate settings for different materials. I see a lot of people buy the cheapest drilling machine they can find, only to realize it doesn’t let them adjust feed rate properly. Then they’re stuck with a machine that can’t drill accurate holes without ruining tools.
Let me wrap this up with some quick tips I give every customer when they’re asking about feed rate:
- Always test on a scrap piece first. No exceptions. Even if you’re drilling the same material you used last week, test a scrap to make sure your machine and bit are aligned.
- Match feed rate to material, bit size, and machine type. Don’t use a wood feed rate for steel, and don’t use a small bit’s feed rate for a large bit.
- If you’re using a manual drill press, add a feed rod or digital gauge. It takes the guesswork out and makes your work consistent.
- For CNC machines, program feed rate as a separate step from spindle speed. Don’t just use the “fastest” setting—balance speed with tool life and part quality.
At the end of the day, feed rate isn’t just a number. It’s what separates a amateurish hole that snaps your bit and ruins your part from a clean, accurate hole that saves you time and money. I’ve been selling drilling machines for years, and the number one mistake I see new operators make is not understanding feed rate. It’s simple once you get the hang of it, and it makes such a big difference in how your shop runs.
If you’re shopping for a new drilling machine, or you have questions about how feed rate works for your specific jobs, don’t hesitate to reach out. We can help you pick the right machine, walk you through setting feed rate, and even give you tips tailored to your work. Whether you’re a one-person woodworking shop or a production machining facility, we’ve got drilling machines that fit your needs, no guesswork required. I’m here to help you get the most out of your equipment, so your holes are clean, your tools last, and your production runs smoothly.
Vertical Machining Center References
- Stephen F. Krar, Arthur R. Gill, and Peter G. Smith, Machine Shop Technology, 7th Edition, Industrial Press, 2013.
- American Society of Mechanical Engineers (ASME), B5.49-2017: Test Code for Drilling Machines, ASME International, 2017.
- Tooling U-SME, “Drilling Principles: Feed Rate and Spindle Speed,” SME Education Foundation, 2021.
- Colin H. Simmons, Linden Laws, and Jack P. DeVries, Manual of Drilling Practice, Industrial Press, 2005.
Weiss Machinery Co., Ltd.
As one of the most professional drilling machine manufacturers and suppliers in China, we have world-leading production equipment and strong manufacturing capabilities. Please rest assured to buy bulk customized drilling machine at competitive price from our factory. Also, quotation is available.
Address: No. 8 Chunyang Road, Jiangning Binjiang Development Zone, Jiangning District, Nanjing City, Jiangsu Province, China
E-mail: sales@weiss.com.cn
WebSite: https://www.weisscnc.com/